
Clean drinking water should only ever flow one way: from the main, into your home, and out of your taps. Backflow is what happens when it flows the other way — when water from inside a house, a garden, or an irrigation system is drawn or pushed back into the drinking water supply. It is rare, it is usually invisible, and it is the reason backflow preventers exist. A backflow preventer is a small device, usually fitted where the water supply enters a property or a system, that lets water flow in one direction and stops it flowing back.
This guide explains what backflow is, what a backflow preventer protects, the types you are likely to find in a Brighton home, and why annual testing matters. Brighton Burst Pipe is a referral service, not a plumbing company: when you call (720) 918-0220, we connect you with an independent local provider who can inspect, install, or test a backflow preventer and quote for the work.

What is backflow, and how does it happen?
Backflow happens in two ways. Backsiphonage happens when the pressure in the main supply drops — for example, when a water main breaks, or when firefighters use a large amount of water nearby — and water is sucked back from a house or a garden system into the main. Backpressure happens when the pressure inside a house or a system is higher than the pressure in the main, and water is pushed back the wrong way. Both can carry contaminated water — from a garden hose in a bucket, from an irrigation system, from a boiler, or from a drain — into the drinking water supply.
You do not need a dramatic event for backflow to matter. A garden hose left in a paddling pool, a hose-end sprayer left in a bucket of cleaning chemicals, or an irrigation system connected to the drinking water supply can all be a backflow risk if the pressure drops at the wrong moment. That is why backflow preventers are fitted where a risk exists, and why they are tested regularly — a preventer that has failed is no protection at all.
What does a backflow preventer protect?
A backflow preventer protects the drinking water supply — in your home, and in the homes around you. If contaminated water flows back into the main, it does not just affect your house: it can affect the supply to your neighbours as well. That is why backflow prevention is not just a matter for the homeowner: water providers and local rules often require a preventer, and annual testing, where a risk exists. The exact requirements depend on the system and the local rules, and a provider can tell you what applies to your home.
In a Brighton home, the most common backflow risks are an irrigation or sprinkler system, a garden hose connected to the supply, a boiler or a heating system, and a water softener or a fire sprinkler system. Each of those connects the drinking water supply to something that could contaminate it, and each of them needs the right type of preventer — not just any preventer, but one suited to the risk.
What types of backflow preventer are there?
- Air gap. The simplest protection: a physical gap between the end of a pipe and the water it fills, so water cannot be sucked back. A tap over a sink, with a gap between the tap and the water level, is an air gap.
- Atmospheric vacuum breaker. A small device, often fitted on a hose tap or an irrigation valve, that lets air in when the pressure drops, breaking the siphon. It is simple and cheap, but it is only suitable for low-risk uses and it must be fitted the right way up.
- Pressure vacuum breaker. A device for irrigation systems that protects against backsiphonage, with a spring-loaded check valve and an air inlet. It needs to be fitted above the highest sprinkler head.
- Double check valve assembly. Two check valves in series, for medium-risk uses, that stop water flowing back in either direction. It is a common choice for a whole-house supply or for a system that needs reliable protection.
- Reduced pressure zone assembly. The highest level of protection, with two check valves and a relief valve between them that dumps water if either valve fails. It is used where the risk is highest — for example, where chemicals or a boiler are connected to the supply — and it needs annual testing by a qualified tester.
Which type your home needs depends on the risk, the system, and the local rules. A provider should explain which type is fitted, why it was chosen, and what testing it needs. Do not replace a preventer with a different type without advice — a lower level of protection may not be enough for the risk, and a higher level may need testing that the lower one did not.
Why does a backflow preventer need testing every year?
A backflow preventer is a mechanical device, and its valves, springs, and seals wear out, corrode, and become clogged with scale — especially in Brighton hard water, at 15–20 grains per gallon. A preventer that has not been tested may look fine from the outside and fail when it is needed. Annual testing, by a qualified tester using test equipment, checks that each check valve holds, that the relief valve opens at the right pressure, and that the device still protects the supply.
Testing is often a requirement, not just a recommendation, where a preventer is fitted — for example, for an irrigation system — and the result is usually recorded and reported to the water provider. If a test fails, the preventer needs to be repaired or replaced before it can be used again. Keep a record of each test: the date, the type of device, the result, and any work done. That record is what shows the device has been looked after, and it helps a provider if the device fails in future.

What are the signs a backflow preventer is failing?
- Water leaking from the relief valve. A reduced pressure zone device that drips or discharges water from its relief valve may have a failed check valve, or debris in the valve.
- Low water pressure. A preventer that is clogged with scale or debris can reduce pressure throughout the house or the irrigation system.
- Discoloured or odd-tasting water. Water that is brown, cloudy, or tastes unusual after work on the supply, or after a pressure drop, should be investigated — do not keep drinking it until it has been checked.
- A failed annual test. The clearest sign of all. If the tester says the device has failed, it needs repair or replacement, not another year of use.
- Damage or corrosion. A device that is cracked, corroded, or damaged by freezing needs attention, even if it is still working.
Do not try to test or repair a backflow preventer yourself unless you are qualified to do so. Testing needs specialist equipment and a tester who knows the device, and a repair that is done wrong can leave the supply unprotected. If you notice a leak, a pressure change, or a change in the water, call a provider and tell them what you have seen.
How should you look after a backflow preventer in winter?
In Brighton winters, a backflow preventer fitted outside, or in an unheated space, can freeze and crack. Irrigation systems should be winterised before the first freeze: the system should be drained, the preventer should be protected or removed as the provider advises, and the water supply to it should be turned off. A frozen preventer is a common spring repair, and it is one that is easy to prevent with a winter visit.
Keep the area around the preventer clear and accessible, so it can be tested without moving boxes or stored items. Do not paint over it, do not cover it, and do not turn its shut-off valves unless you know what you are doing. If you are not sure where your preventer is, ask a provider to show you — it is usually near the main shut-off, near the irrigation connection, or where the supply enters the house.
How much does a backflow preventer cost?
The site publishes no figure for a backflow preventer, its installation, or its annual test, so this guide does not invent one. The cost drivers are the type of device, the risk it protects against, whether a new installation or a replacement is needed, and the labour. Labour on this site is listed at $100–$350 per hour, and an emergency call-out at $100–$300, and those are the only figures that apply here. A simple vacuum breaker on a hose tap is a different job from a reduced pressure zone assembly for a whole system, and only a provider who has seen the system can give you a final price. Ask for the device, the installation, and the annual test to be quoted separately, so you can see what each part costs.
Frequently Asked Questions
What is a backflow preventer?
A device that lets water flow in one direction and stops it flowing back into the drinking water supply. It protects your home and your neighbours’ homes from contaminated water being drawn or pushed back into the main.
Do I need a backflow preventer in Brighton?
It depends on the risk in your home — an irrigation or sprinkler system, a boiler, a water softener, or a garden hose connected to the supply are the most common risks. A provider can tell you what applies to your home and what the local rules require.
How often should a backflow preventer be tested?
Usually once a year, by a qualified tester. A preventer that has not been tested may look fine and fail when it is needed, especially in Brighton hard water, at 15–20 grains per gallon, where scale can clog its valves.
What happens if a backflow test fails?
The preventer needs to be repaired or replaced before it can be used again. Keep a record of each test — the date, the type of device, the result, and any work done.
Can I test a backflow preventer myself?
No, not unless you are qualified to do so. Testing needs specialist equipment and a tester who knows the device. A repair done wrong can leave the supply unprotected.
How much does backflow testing cost?
The site publishes no figure for backflow testing. The cost drivers are the type of device and the labour — listed on this site at $100–$350 per hour. Ask a provider for a quote for your home.
Need a backflow preventer tested in Brighton?
If your backflow preventer has not been tested in the last year, if it is leaking, or if you are not sure whether your home has one at all, do not leave it — a preventer that has failed is no protection. Call (720) 918-0220 and we will connect you with an independent local provider in the Brighton area who can find the device, test it, and quote for a repair, a replacement, or a new installation. Tell them whether you have an irrigation system, a boiler, or a water softener — that helps them bring the right equipment and give you a clear price.
